How To Install Gopro Floaty Backdoor

🕓 viii min read

✏️   Updated on 1st March 2022

Intro

Hola my surfing amigos… I'thousand dorsum with another blog post, and this time we're discussing 'How To Install GoPro Surfboard Mount'.

I've seen so many incorrect videos about this topic online, so thought I'd show you the correct way to install a GoPro surfboard mountain. We'll discuss two installation methods; the recommended method and the universal method. If you're not able to do the first, y'all'll definitely exist able to exercise the second.

i. How To Install GoPro Surfboard Mount Video
two. You Volition Need…
3. Steps To Follow
4. Tips To Continue Your GoPro Prophylactic

Both methods are really like shooting fish in a barrel, so allow's get started!

1. How To Install GoPro Surfboard Mount Video

two. You Will Demand…

• i x GoPro surfboard mount kit, which should include…
  • • GoPro Surfboard mountain
    • Adhesive anchor
    • Photographic camera tether
    • Locking plug
• 1 x Your GoPro / GoPro case
• one x Standard GoPro mount
• 2 10 Cotton pads / tissue
• i ten Standard GoPro thumbscrew
• 1 x Warm soapy water / white spirit / methylated spirit

3. Steps To Follow

Step #1 – Remove any residue

The first stride is to remove whatsoever oily residuum where you're going to be placing your surfboard mountain. Former wax commonly leaves a bit of oiliness and so removing it helps the surfboard mount bond properly.

Yous can do this by using white spirit, methylated spirit or warm soapy h2o and some cotton wool pads or tissues. Information technology shouldn't take too long with a few circular and up and down motions (Epitome ane).

Prototype 1

One time whatever oily stuff is removed, dry the remaining moisture off with some more cotton pads or tissues (Image 2). This will too help the surfboard mount bond properly to your surfboard.

Epitome ii

Step #2 – Attach your GoPro surfboard mount

Now the area is ready, the next step is to attach your GoPro surfboard mount. Before doing annihilation though, accept a quick read of the 'Tips for surfboard mount placement' bullet points just below.

Then, the placement is up to you but if you're unsure I'd recommend placing it in the centre (Paradigm 3). By placing it in the centre, your GoPro volition be able to get the widest angle of you surfing.

Paradigm 3

If yous've got a visible stringer (like I accept) you lot can utilise that for guidance, only if not just give information technology your best guess. Once fastened, give it a expert press down.

Tips for surfboard mount placement…

• Don't place information technology besides far dorsum – If you practice your GoPro will be annoyingly close to your face whilst you're paddling.
• Don't place it too close to the nose – If you exercise water will hitting your GoPro whilst yous're on a wave and force it down to point at your surfboard rather than you.

Step #3 – Attach your adhesive anchor

With the surfboard mount in place, all that's left to stick on is your adhesive ballast. This matter simply actually has one place to go and so it's really easy (Paradigm four).

Epitome 4

For neatness, I like to place the anchor at a right angle to the surfboard mount. Only this is just my inner OCD expressing itself and not actually that of import – and then permit's move on.

Step #four – Look 24 hours

The next bit is both the easiest and the hardest – waiting the recommended 24 hours.

The reason GoPro recommend this is because it gives your new surfboard mount time to bail properly with your surfboard.

Yes… existent life bonding time.

If y'all're going through this process with the idea of hitting the waves straight after, that's up to you. Only, if you lot don't expect the 24 hours there is a higher chance of your surfboard mount and shiny GoPro falling off. You accept been warned.

Stride #5 – Attach your camera tether

After patiently waiting 24 hours, this is where things get a scrap fiddly. Information technology also gets a bit difficult to explain using the ability of words… so if none of this brand sense, the video is at the top of this post.

Showtime matter is to feed your camera tether through the hole in your adhesive anchor (Epitome v).

Image v

In one case through, put the photographic camera tether through it's ain loop and pull tight (Image 6). If you've washed it correctly, you should accept something that looks like this…

Image six

Step #6 – Slot in your standard GoPro mount

This step is piece of cake.

Grab your standard GoPro mount and slot that bad boy straight into your surfboard mount until you lot hear a 'click' (Image 7). Your setup should now look something like this…

Epitome seven

Step #vii – Push in your locking plug

With your standard GoPro mount in place, all we need to practise is secure it using the locking plug.

Button your locking plug into the dorsum part of the standard GoPro mount until it can't go any farther (Epitome viii). This is an essential part of the setup and volition stop the standard GoPro mount from unclipping.

Prototype eight

Step #8 – Thumbscrew through the loop

Adjacent, feed your standard GoPro thumbscrew through the locking plug loop (Prototype 9).

Image 9

One time washed, we're gear up to actually tether your GoPro to your surfboard mount (finally)!

Stride #ix – Tethering your GoPro

Now y'all're ready to tether your GoPro, I'm going to take you through 2 methods (again, it might be easier to watch the video above for this next scrap).

1. The 'Recommended by GoPro' method – All-time possible manner to adhere your GoPro to your surfboard mount but is dependent on the GoPro model and/or GoPro case you have.
2. The 'Universal' method – Not as good as the starting time method simply can be accomplished with any GoPro model or GoPro example.

Allow's start with the 'recommended by GoPro' method…

Footstep #10 – Tethering your GoPro (Recommended by GoPro method)

To do this method you need a GoPro instance that allows you to remove the backdoor. If you've got one of those continue reading – if not, caput on downward to Step #11 for the universal method.

So, those still reading should have a GoPro instance with a removable backdoor. First footstep is to remove the backdoor from your GoPro instance, it should look a bit similar the epitome below (Image 10).

Paradigm 10

Next pace is to feed your camera tether through the gap between the backdoors metal bar and the backstairs itself (Image eleven).

Image 11

In one case the tether is through the gap, take the looped end of the tether and pass it around the unabridged backstairs. If you've washed information technology correctly it should look a bit like the below and you'll exist able to pull it tight to secure it (Image 12).

Image 12

At present the backdoor is secured, you just need to re-adhere the rest of your GoPro example (Prototype 13).

Prototype 13

When that's sorted simply slot your GoPro case into the standard GoPro mountain and tighten it upward with your standard GoPro thumbscrew (Image fourteen).

Image 14

And you've done it! This is by far the all-time way to attach your GoPro to your surfboard mount – did I mention GoPro recommend it?

Footstep #11 – Tethering your GoPro (Universal method)

This second method is great every bit it works perfectly with every GoPro and/or GoPro case. It's also less fiddly than the first method making it easier to describe (full video guidance is still available above though… just saying).

First step, take your camera tether and guide one of the strings through the gap between the ii prongs at the bottom of your GoPro / GoPro case (Image 15).

Image fifteen

Then, only slot your GoPro / GoPro case into the standard GoPro mount whilst keeping the camera tether in-between the ii prongs.

Prototype sixteen

Final pace is to tighten information technology all up using your standard GoPro thumbscrew (Image 16) and you're done!

4. Tips to go along your GoPro safe

Before catastrophe the mail service I wanted to give you two quick tips to consider earlier going surfing…

1. Get a GoPro floaty / floaty backstairs

If you're unfamiliar with the humble floaty, it's basically a floatation device for your GoPro. If your GoPro were to come off your surfboard whilst amongst the waves, this thing would save it.

It's ability to hold your GoPro above the water and the fact it's so brilliant gives you the best shot of keeping your GoPro safe if it were to autumn off.

This tip is especially important for those with foam surfboards. GoPro has mentioned their surfboard mounts don't bond as well with foam surfboards (so basically definitely go one of these things).

I'chiliad confident the above guide will help continue your GoPro stuck to your surfboard, but it'due south skillful to accept an additional rubber internet.

2. Wait the 24 hours GoPro recommend

This shouldn't be too hard, merely I empathize with those wanting to use information technology for the first fourth dimension straight after setting it up.

However, GoPro do recommend the 24 hour flow for a reason and it'south all most that precious bonding time. The only reason I waited the 24 hours is because if I didn't and my GoPro vicious off, I'd feel like an idiot.

Exist patient team, I know you lot can do information technology!

Summary

So all, if you've made it this far – top marks. I'm hoping my 'How To Install GoPro Surfboard Mountain' guide has helped a lilliputian on your journey to surfing nirvana. If yous did observe it useful, information technology would be corking to hear from yous in the comments beneath.

As always, be certain to follow on the usual socials below to proceed upward to date with the latest surfing content!

Follow on:

Next read: 'How To Safely Wipeout When Surfing'

---

---

Source: https://thewaveshack.com/how-to-videos/how-to-install-gopro-surfboard-mount/

Posted by: wingerplect1956.blogspot.com

Share this post